Delma's Dresden Tutorial

I remember my grandma making a Dresden Plate quilt many years ago, and I thought,
I will NEVER make one of those!  I think she worked on those Dresden Plates for years,

and it just seemed so hard and so tedious!  But then I discovered the EZ Dresden Ruler by

Darlene Zimmerman, and it took out all of the guesswork!  I fell in love with Dresdens

and have made several Dresden Plate quilts since then!  

So today, I have a little tutorial for you that features one big Dresden Plate.  This is the

perfect project to showcase some of your favorite fabrics and let you try your hand at a

Dresden Plate, if you haven't made one before.  

I'm calling this one Delma's Dresden - in honor of my late grandmother.  It's more modern
than the classic ones she used to make, but I've been wanting to make this kind of Dresden Plate

for a long time.  It doesn't have a center circle appliquéd over the smaller edges of the wedges.

I think it's pretty fun with points on the outside and inside of each wedge.

Supplies Needed:

- 20 bright rectangles, 4" x 6" each

- Cream background fabric: 28" x 28"

- Batting: 28" x 28"

- Backing fabric: 28" x 28"

- Binding fabric: 1/3 yard or a 26" x 26" frame

- EZ Dresen Ruler By Darlene Zimmerman

- Wood Point Turner

- Spray Starch 

- Appli-Glue by Jilily Studio

- Basting pins or spray, walking foot, water soluble pen,

and seam guides if machine quilting it yourself

- Other quiltmaking supplies such as a sewing machine, iron and board,

rotary cutter, ruler and mat, coordinating thread and applique needle, etc.

Step 1. Line up the 2" mark of the EZ Dresden Ruler on the bottom edge of a bright 

4" x 6" rectangle and the top edge of the ruler on the top edge of the rectangle.  

Trim off the sides to create a fabric wedge.  Cut 20 wedges.

Step 2: Fold the wedges in half, right sides together.  Sew across the top and bottom edges using a 

1/4" seam allowance (I did this in a chain, which is why they're in an arc, below left).  

Trim the corners near the folded edges to reduce bulk.  Be careful not to clip the stitches.

Step 3: Press the folded edges with a hot iron to mark the center of the wedges.

Turn the wedges right-side-out and use a wood point turner to carefully push out

the top and bottom points so they are nice and sharp.  Align the seam allowances (on the back side)

with the center crease to make sure the points are centered.  Press the "blades" with a hot iron

(use spray starch to get nice crisp edges).  Make 20.

    
  

Step 4: Using a 1/4" seam allowance, sew the blades together along the long edges,

right sides together.  Make sure the bigger points are aligned at the top and the smaller points

are aligned at the bottom.  Sew the edges of the first and last blades together to create a

Dresden Plate.  Press the seam allowances in one direction.

   

Step 5: Press the background fabric in half with a hot iron, in both directions, to mark the

center of the square.  Center your Dresden Plate on the background fabric over the creases.

Use small dots of Appli-Glue underneath the points of the wedges to adhere the Dresden Plate

in place.  I like to work in quarter sections of the Dresden Plate, just lifting up points of the

wedges and putting a few dots of glue on the back side of each.  Once everything

is glued in place, I like to "set it" with a hot iron.  

Note: My Dresden Plate was off-center here, and I didn't notice until I had already glued

it in place.  Thankfully, the background fabric was cut a little oversized, so I had room to

center it later when I squared everything up and cut it down to size.

Step 6. Applique the Dresden Plate to the background fabric.  I hand-appliqued mine using

taupe colored thread.  If you don't like to hand-stich, you could machine appliqué it

with a simple top-stitch or decorative stitch.  Carefully press

the quilt top with a hot iron.

Step 7: Lay down your backing fabric (wrong side up) on a smooth surface.

Then layer with a piece of batting and your quilt top (right side up).  Use basting pins to

secure the 3 layers together, placing pins 3-4 inches apart.

Step 8: Quilt as desired.  I used my walking foot and seam guides to quilt

diagonal lines (both directions) 1" apart.  I like to increase my stitch length a little when I'm

machine quilting so the stitches aren't too tiny and once in a while I had to use a water soluble pen

and a ruler to mark a few of the lines. I used matching cream thread and avoided the

Dresden Plate as I stitched the diagonal lines.  My machine has a button to create a knot so I used that whenever I had to stop or start a new line.  Once I was done with that part, I went back and

stitched in the ditch around the entire Dresden Plate and each blade.  There was lots of starting and stopping as I tried to reduce the amount of overlapped stitching.

Step 9.  Square up the quilt to your desired size.  Then bind or frame it.

If binding it, use 3 strips, 2-1/2" x 40" each.

I trimmed off as little as possible and then my husband built a 26" x 26" frame for it.  

I got 1/4" plywood for the back (Home Depot sells 26" x 26" boards)

and 1" x 2" wood boards for the sides (I believe we used alder).  My husband assembled

the frame and notched out space with a router for the plywood and quilt.  I stained it

and then he attached some simple hardware to the back so we could hang it.

He assembled everything and then he trimmed off any excess quilt that was poking out

behind the plywood with a sharp Exacto knife.

I love how it turned out and am so thankful to my husband for building the frame!

This would be super cute bound like a normal wallhanging or turned into a pillow

if you don't have the means to build a frame. 

Let me know if you decide to make this project!  Even better, you can send me photos at gigisthimble@hotmail.com or tag me on Instagram at @gigis_thimble.  I'd love to see it!

This is a fun way to showcase your favorite fabrics or try your hand at a Dresden Plate,

applique, or machine quilting.  I used strike-off (sample) fabrics from my latest fabric collection

with Riley Blake Designs called Honey Locust.

Thanks for stopping by today and please let me know if you have any questions!